Lenovo ThinkServer TD200 Instrukcja Użytkownika Strona 145
- Strona / 228
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Do not insert a memory DIMM in this connector.This DIMM slot is not supported in this model.
Do not insert a memory DIMM in this connector.This DIMM slot is not supported in this model.
Do not insert a memory DIMM in this connector.This DIMM slot is not supported in this model.
Do not insert a memory DIMM in this connector.This DIMM slot is not supported in this model.
1 Alignment bracket
2 Virtual media key (rear)
3 Virtual media key (front)
4 Retention tab
5 Virtual media key connector
9. Reinstall any adapters that you removed earlier.
10. Rotate the rear adapter retention bracket to the closed (locked) position.
11. Reinstall the side cover (see “Installing the side cover” on page 134).
12. Lock the side cover.
13. Reconnect the external cables and power cords; then, turn on the attached
devices and turn on the server.
Removing the control-panel assembly
To remove the control-panel assembly, do the following:
1. Read the safety information (see “Safety” on page vii and “Installation
guidelines” on page 37).
2. Turn off the server and all attached devices; then, disconnect all power cords
and external cables.
3. Unlock and remove the side cover (see “Removing the side cover” on page
43).
4. Open the bezel. Place your finger on the pull point area on the left side of the
bezel door and rotate it away from the server.
Chapter 5. Installing optional devices and replacing customer replaceable units 127
- Installation and User Guide 1
- Contents 5
- Contents v 7
- Safety ix 11
- Safety xi 13
- Safety xiii 15
- Safety xv 17
- Chapter 1. Introduction 19
- Related documentation 21
- Features and technologies 25
- Specifications 27
- Software 30
- EasyStartup 30
- EasyManage 30
- Front view 33
- 1 Power-on LED 6 USB 1 35
- Operator information panel 37
- EasyLED diagnostic panel 38
- Rear view 44
- System-board LEDs 51
- Server power features 53
- Turning on the server 53
- Turning off the server 53
- Installation guidelines 55
- System reliability guidelines 56
- Opening the bezel 58
- Removing the side cover 61
- Removing the air baffle 62
- 1 Fan cage assembly 65
- 2 Power-supply release tab 70
- 2 Hinge pins 71
- Removing the battery 72
- Installing the battery 73
- 1 Positive (+) side 74
- Removing a DVD drive 77
- Installing a DVD drive 80
- 1 EMC shield 82
- 2 Optical drive 82
- 3 Optical drive rails 82
- 1 Optical drive power cable 83
- 2 Tape drive 86
- 3 Drive tray 89
- 4 Hard disk drive 89
- 2 Drive tray 90
- 4 Release latch 90
- 5 Hard disk drive 90
- 1 Filler panels 94
- 2 Drive-bay EMC shield 94
- Removing a power supply 97
- Installing a power supply 100
- 2 Power supply assembly 101
- Removing a hot-swap fan 102
- Installing a hot-swap fan 103
- Removing a memory module 104
- 1 Power supply 105
- 2 Power-supply handle 105
- Installing a memory module 107
- 12 Dual-rank DIMMs 4 GB 48 GB 108
- 1 DIMM 112
- 2 Retaining clip 112
- Removing an adapter 113
- Installing an adapter 114
- 1 Adapter 117
- 1 Microprocessor 121
- 2 Alignment triangles 121
- 3 Notches 121
- 2 Power supply release tab 123
- 2 PCI slot 1 125
- 1 Adapter connector 128
- 2 Signal cable 128
- 1 ServeRAID adapter 131
- 2 Battery carrier 131
- 3 Battery 131
- 1 Alignment bracket 144
- 2 Virtual media key (rear) 144
- 3 Virtual media key (front) 144
- 4 Retention tab 144
- 1 Release latch 147
- 2 Control panel assembly 147
- Completing the installation 148
- Closing the bezel 148
- 1 Bezel 149
- 2 Hinge assembly 149
- 3 Retention tabs 149
- Installing the air baffle 150
- 1 Air baffle pinch tab 151
- 2 Air baffle 151
- Installing the side cover 152
- Connecting the cables 152
- Connecting external devices 154
- Using the Setup Utility 156
- Starting the Setup Utility 156
- Setup Utility menu choices 156
- Passwords 159
- Configuring RAID controllers 160
- Formatting a hard disk drive 162
- Using the WebBIOS utility 163
- Starting the WebBIOS utility 163
- Using the EasyStartup DVD 165
- Configuring RAID 166
- EasyStartup overview 166
- Updating the firmware 169
- 2 Clear CMOS jumper (JP1) 171
- 3 SW6 switch block 171
- Automated boot recovery (ABR) 172
- Three boot failure 172
- Installation requirements 178
- Installation order 178
- Chapter 7. Troubleshooting 181
- Diskette drive problems 182
- General problems 183
- Hard disk drive problems 183
- Intermittent problems 184
- Memory problems 185
- Microprocessor problems 186
- Monitor or video problems 186
- Optional-device problems 188
- Power problems 189
- Serial port problems 190
- Software problems 191
- Solving undetermined problems 191
- Solving SCSI problems 192
- Solving power problems 193
- Event logs 194
- POST error codes 196
- Before you call 205
- Using the documentation 205
- Calling for service 206
- Using other services 206
- Lenovo product service 207
- Appendix B. Notices 209
- Trademarks 210
- Important notes 210
- Appendix B. Notices 193 211
- Hazardous Substances 212
- Battery return program 213
- Appendix B. Notices 197 215
- Appendix B. Notices 199 217
- Index 203 221
- Index 205 223
- Index 207 225
- Part Number: 44W2344 228
- Printed in USA 228
- (1P) P/N: 44W2344 228
Powiązane produkty i podręczniki dla Sprzęt komputerowy Lenovo ThinkServer TD200
(36 strony)
(80 strony)Powerskin Fournisseurs d'énergie manuels d'utilisation
La liste de Powerskin Fournisseurs d'énergie produits contient 11 manuels d'utilisation pour les modèles 11. Tous les guides d'utilisation en format pdf peuvent être téléchargés ou consultés en ligne.
Komentarze do niniejszej Instrukcji